| 2 |
|
Basilisk II, Version 0.8 |
| 3 |
|
A free, portable Mac II emulator |
| 4 |
|
|
| 5 |
< |
Copyright (C) 1997-1999 Christian Bauer et al. |
| 5 |
> |
Copyright (C) 1997-2000 Christian Bauer et al. |
| 6 |
|
Freely distributable |
| 7 |
|
|
| 8 |
|
|
| 332 |
|
Linux: |
| 333 |
|
The "ethernet card description" is the name of an Ethernet interface. |
| 334 |
|
There are two approaches to networking with Basilisk II: |
| 335 |
+ |
|
| 336 |
|
1. Direct access to an Ethernet card via the "sheep_net" driver. |
| 337 |
|
In this case, the "ethernet card description" must be the name |
| 338 |
|
of a real Ethernet card, e.g. "eth0". It also requires the "sheep_net" |
| 342 |
|
networking. MacOS will only be able to talk to other machines on |
| 343 |
|
the Ethernet, but not to other networks that your Linux box routes |
| 344 |
|
(e.g. a second Ethernet or a PPP connection to the Internet). |
| 345 |
+ |
|
| 346 |
|
2. Putting Basilisk II on a virtual Ethernet via the "ethertap" device. |
| 347 |
|
In this case, the "ethernet card description" must be the name |
| 348 |
|
of an ethertap interface, e.g. "tap0". It also requires that you |
| 349 |
|
configure your kernel to enable routing and the ethertap device: |
| 350 |
|
under "Networking options", enable "Kernel/User netlink socket" and |
| 351 |
|
"Netlink device emulation", under "Network device support", activate |
| 352 |
< |
"Ethertap network tap". Next, see /usr/src/linux/Documentation/ |
| 353 |
< |
networking/ethertap.txt for information on how to set up /dev/tap* |
| 354 |
< |
device nodes and activate the ethertap interface. Under MacOS, |
| 355 |
< |
select an IP address that is on the virtual network and set the |
| 356 |
< |
default gateway to the IP address of the ethertap interface. This |
| 357 |
< |
approach will let you access all networks that your Linux box has |
| 358 |
< |
access to (especially, if your Linux box has a dial-up Internet |
| 359 |
< |
connection and is configured for IP masquerading, you can access |
| 360 |
< |
the Internet from MacOS). The drawback is that you can only use |
| 361 |
< |
network protocols that Linux can route, so you have to install and |
| 362 |
< |
configure netatalk if you want to use AppleTalk. |
| 352 |
> |
"Ethertap network tap". You also have to modify devices/net/ethertap.c |
| 353 |
> |
a bit before compiling the new kernel: |
| 354 |
> |
|
| 355 |
> |
- insert "#define CONFIG_ETHERTAP_MC 1" near the top (after the |
| 356 |
> |
#include lines) |
| 357 |
> |
- comment out the line "dev->flags|=IFF_NOARP;" in ethertap_probe() |
| 358 |
> |
|
| 359 |
> |
Next, see /usr/src/linux/Documentation/networking/ethertap.txt for |
| 360 |
> |
information on how to set up /dev/tap* device nodes and activate the |
| 361 |
> |
ethertap interface. Under MacOS, select an IP address that is on the |
| 362 |
> |
virtual network and set the default gateway to the IP address of the |
| 363 |
> |
ethertap interface. This approach will let you access all networks |
| 364 |
> |
that your Linux box has access to (especially, if your Linux box has |
| 365 |
> |
a dial-up Internet connection and is configured for IP masquerading, |
| 366 |
> |
you can access the Internet from MacOS). The drawback is that you |
| 367 |
> |
can only use network protocols that Linux can route, so you have to |
| 368 |
> |
install and configure netatalk if you want to use AppleTalk. Here is |
| 369 |
> |
an example /etc/atalk/atalkd.conf for a LAN: |
| 370 |
> |
|
| 371 |
> |
eth0 -seed -phase 2 -net 1 -addr 1.47 -zone "Ethernet" |
| 372 |
> |
tap0 -seed -phase 2 -net 2 -addr 2.47 -zone "Basilisknet" |
| 373 |
> |
|
| 374 |
> |
(the "47" is an arbitrary node number). This will set up a zone |
| 375 |
> |
"Ethernet" (net 1) for the Ethernet and a zone "Basilisknet" (net 2) |
| 376 |
> |
for the internal network connection of the ethertap interface. |
| 377 |
> |
MacOS should automatically recognize the nets and zones upon startup. |
| 378 |
> |
If you are in an existing AppleTalk network, you should contact |
| 379 |
> |
your network administrator about the nets and zones you can use |
| 380 |
> |
(instead of the ones given in the example above). |
| 381 |
|
|
| 382 |
|
AmigaOS: |
| 383 |
|
You have to specify the name of the SANA-II Ethernet device and the device |
| 653 |
|
- Bill Huey <billh@mag.ucsd.edu>: 15/16 bit DGA and 15/16/32 bit X11 |
| 654 |
|
window support |
| 655 |
|
- David Lawrence <davidl@jlab.org>: incremental window refresh code |
| 656 |
+ |
- Samuel Lander <blair_sp@hotmail.com>: tile-based window refresh code |
| 657 |
|
- Gwenole Beauchesne <gb@dial.oleane.com>: SPARC assembly optimizations and |
| 658 |
|
fbdev video code |
| 659 |
|
- and others... |
