| 1 |
|
|
| 2 |
< |
Basilisk II, Version 0.8 |
| 3 |
< |
A free, portable Mac II emulator |
| 2 |
> |
Basilisk II |
| 3 |
> |
A 68k Macintosh emulator |
| 4 |
|
|
| 5 |
< |
Copyright (C) 1997-2000 Christian Bauer et al. |
| 6 |
< |
Freely distributable |
| 5 |
> |
Copyright (C) 1997-2001 Christian Bauer et al. |
| 6 |
|
|
| 7 |
|
|
| 8 |
|
License |
| 15 |
|
Overview |
| 16 |
|
-------- |
| 17 |
|
|
| 18 |
< |
Basilisk II is a free, portable, Open Source 68k Mac emulator. It requires |
| 19 |
< |
a copy of a Mac ROM and a copy of MacOS to run. Basilisk II is freeware and |
| 20 |
< |
distributed under the GNU General Public License. |
| 18 |
> |
Basilisk II is an Open Source 68k Macintosh emulator. That is, it enables |
| 19 |
> |
you to run 68k MacOS software on you computer, even if you are using a |
| 20 |
> |
different operating system. However, you still need a copy of MacOS and |
| 21 |
> |
a Macintosh ROM image to use Basilisk II. |
| 22 |
|
|
| 23 |
|
Basilisk II has currently been ported to the following systems: |
| 24 |
|
- BeOS R4 (PowerPC and x86) |
| 327 |
|
BeOS: |
| 328 |
|
It doesn't matter what you give as "ethernet card description", Basilisk II |
| 329 |
|
will always use the first Ethernet card it finds as long an an "ether" |
| 330 |
< |
line exists (e.g. say "ether yes"). As Basilisk II requires the sheep_net |
| 331 |
< |
net server add-on from SheepShaver, you can only use Ethernet on PowerPC |
| 332 |
< |
machines. |
| 330 |
> |
line exists (e.g. say "ether yes"). Using Ethernet requires the "sheep_net" |
| 331 |
> |
Net Server add-on to be installed. The first time you start Basilisk II |
| 332 |
> |
with Ethernet enabled you will be asked whether it's OK to make the |
| 333 |
> |
necessary changes to your BeOS network configuration to enable sheep_net. |
| 334 |
|
|
| 335 |
|
Linux: |
| 336 |
|
The "ethernet card description" is the name of an Ethernet interface. |
| 352 |
|
configure your kernel to enable routing and the ethertap device: |
| 353 |
|
under "Networking options", enable "Kernel/User netlink socket" and |
| 354 |
|
"Netlink device emulation", under "Network device support", activate |
| 355 |
< |
"Ethertap network tap". You also have to modify devices/net/ethertap.c |
| 355 |
> |
"Ethertap network tap". You also have to modify drivers/net/ethertap.c |
| 356 |
|
a bit before compiling the new kernel: |
| 357 |
|
|
| 358 |
|
- insert "#define CONFIG_ETHERTAP_MC 1" near the top (after the |
| 382 |
|
your network administrator about the nets and zones you can use |
| 383 |
|
(instead of the ones given in the example above). |
| 384 |
|
|
| 385 |
+ |
FreeBSD: |
| 386 |
+ |
The "ethertap" method described above also works under FreeBSD, but since |
| 387 |
+ |
no-one has found the time to write a section for this manual, you're on |
| 388 |
+ |
your own here... |
| 389 |
+ |
|
| 390 |
|
AmigaOS: |
| 391 |
|
You have to specify the name of the SANA-II Ethernet device and the device |
| 392 |
|
unit as "<device name>/<unit>" (e.g. "ariadne.device/0"). If the given |
