--- BasiliskII/README	2004/05/09 16:15:36	1.38
+++ BasiliskII/README	2008/10/01 10:34:34	1.46
@@ -2,7 +2,7 @@
   Basilisk II
   A 68k Macintosh emulator
 
-  Copyright (C) 1997-2004 Christian Bauer et al.
+  Copyright (C) 1997-2008 Christian Bauer et al.
 
 
 License
@@ -26,7 +26,7 @@ Basilisk II has currently been ported to
     IRIX 6.5)
   - AmigaOS 3.x
   - Windows NT 4.0 (mostly works under Windows 95/98, too)
-  - Mac OS X 10.1, 10.2
+  - Mac OS X 10.1 thru 10.4
 
 Some features of Basilisk II:
   - Emulates either a Mac Classic (which runs MacOS 0.x thru 7.5)
@@ -362,7 +362,7 @@ ether <ethernet card description>
 
   Linux:
     The "ethernet card description" is the name of an Ethernet interface.
-    There are three approaches to networking with Basilisk II:
+    There are four approaches to networking with Basilisk II:
 
       1. Direct access to an Ethernet card via the "sheep_net" kernel module.
          The "ethernet card description" must be the name of a real Ethernet
@@ -442,6 +442,12 @@ ether <ethernet card description>
          instead of sending packets via physical media writes them to
          the user space program.
 
+         Prerequesties:
+         - Make sure the "tun" kernel module is loaded
+           # modprobe tun
+         - Make sure IP Fordwarding is enabled on your system
+           # echo 1 >/proc/sys/net/ipv4/ip_forward
+
          A virtual network configuration script is required and the
          default is /usr/local/BasiliskII/tunconfig unless you specify
          a different file with the "etherconfig" item.
@@ -455,6 +461,37 @@ ether <ethernet card description>
            #!/bin/sh
            exec /usr/bin/kdesu -c /path/to/tunconfig $1 $2
 
+      4. Access the network through the user mode network stack.
+         (the code and this documentation come from QEMU)
+
+         By setting the "ethernet card description" to "slirp",
+         Basilisk II uses a completely user mode network stack (you
+         don't need root priviledges to use the virtual network). The
+         virtual network configuration is the following:
+
+           Basilisk II <------> Firewall/DHCP server <-----> Internet
+           (10.0.2.x)      |         (10.0.2.2)
+                           |
+                           ----> DNS server (10.0.2.3)
+                           |
+                           ----> SMB server (10.0.2.4)
+
+         Basilisk II behaves as if it was behind a firewall which
+         blocks all incoming connections. You can use a DHCP client to
+         automatically configure the network in Basilisk II.
+
+         In order to check that the user mode network is working, you
+         can ping the address 10.0.2.2 and verify that you got an
+         address in the range 10.0.2.x from the Basilisk II virtual
+         DHCP server.
+
+         Note that ping is not supported reliably to the internet as
+         it would require root priviledges. It means you can only ping
+         the local router (10.0.2.2).
+
+         When using the built-in TFTP server, the router is also the
+         TFTP server.
+
   FreeBSD:
     The "ethertap" method described above also works under FreeBSD, but since
     no-one has found the time to write a section for this manual, you're on
@@ -467,6 +504,10 @@ ether <ethernet card description>
     not an Ethernet device, Basilisk II will display a warning message and
     disable Ethernet networking.
 
+  Mac OS X:
+    The "slirp" method described above now seems to work.
+
+
   See the next item for an alternative way to do networking with Basilisk II.
 
 udptunnel <"true" or "false">
@@ -939,7 +980,7 @@ And another mailing list for Basilisk II
   http://lists.sourceforge.net/lists/listinfo/basilisk-devel
 
 Some general advice about asking technical support questions can be found at
-  http://www.tuxedo.org/~esr/faqs/smart-questions.html
+  http://www.catb.org/~esr/faqs/smart-questions.html
 
 Keeping this in mind will greatly increase your chances of getting a useful
 answer.